The Hidden Pitfalls of Intelligent Lighting

For most of us, the first brush with an automated system in a building had to do with the light system – specifically occupancy or motion sensors. These automated systems turn on the lights when someone is occupying the area, and they turn off the lights when nobody is there.

The main draw of automated lighting lies in its ability to help make energy use more efficient in buildings. However, while automated lighting seems like an easy plug and play solution, building owners should take a closer look at the installation and consider any drawbacks carefully. As is often the case with technology, what works in theory might have deal-breaking challenges in practice. Let’s take a look at four downsides to sensor-based lighting control in the office.

Downside #1: Limited area of use

Sensor placement and installation are subject to a long list of rules and best practices just to get standard results. A 90+ page guide on sensor placement is not uncommon.

When all factors are considered, only a few areas like toilets, alley ways and storage closets are suitable for motion sensor use.  Moreover, it’s difficult to be confident about your reliance on sensors if so many things can be done incorrectly.

One of our customers installed motion sensors for their meeting rooms. Soon after, they received consistent complaints from several women about the sensors not working. It turned out that the sensors were placed too high and were not detecting relatively shorter people entering the room. Fixing the problem was time-consuming and costly.

Downside #2: Practical difficulties

There aren’t many things more frustrating than a motion sensor that doesn’t work as expected. Whether it’s because of bad placement, low batteries, or some form of interference, sensors do experience problems from time to time.

These problems can cause energy wastage or worse – staff frustration and increased stress levels. In 2010, a guest sued a hotel when she fell and injured herself in the toilet – the motion sensor had turned off the lights[1].

Sometimes it’s not even the fault of the sensors. We’ve seen significant investments in motion sensors go down the drain because of traditional occupants’ behaviours. For instance, a quick trip to the toilet before heading home in the evening can result in half the office lights turning on for 10 minutes – not exactly energy saving.

Downside #3: Higher costs, longer payback

Adding sensors to your lighting control system increases the lifetime cost of the system.

First, there’s the cost of the sensors themselves. Second, there’s the expertise required to place them and calibrate them correctly, which takes time and money. Third, there’s the ongoing cost of ensuring that your sensor-control layout matches your changing office. Doing this often requires rewiring and relocation of sensors.

If all of these deliver more savings than the extra costs, then it’s worthwhile. The problem is that this is rarely the case. Sensors that control lights in zones usually save LESS energy than individual fixture control without sensors.

The lack of precision counteracts the benefits of the sensors. And if you install one sensor per fixture, your payback could get even worse. You end up drastically increasing costs in exchange for only minor extra savings. Payback in these cases takes as long as 4-7 years[2].

Downside #4: Lower productivity

To get the most out of your staff, you need to provide a focused environment, a sense of control over their working areas, and a sense of ownership. And yet sensor-based lighting control can detract from this feeling.

It distracts occupants with lights frequently turning on/off. More generally, it subjects them to a frustrating automated system that does not always respond to their needs.

We’ve seen cases where the entire control system has been removed due to occupant dissatisfaction with sensor-based control. Unfortunately, the sensors were the only way to control the lights, so when they were taken out, all of the benefits of scheduling and optimization went with them.

Avoiding pitfalls and ensuring results

If you’re considering sensors for your office lighting controls, make sure you understand what you’re getting into. Otherwise, you could end up writing off a significant investment. Sensors have their place in some limited contexts, but the question you must ask is: do you want sensors, or do you want results?

A good lighting system must be able to meet both your design and operational needs. The powerful and inherent energy savings benefits of lighting control can only be realised if your system is installed to the right standards.

Today, building owners need solutions such as En-trak Smart Lighting which is easy to use, affordable and wireless. It provides a flexible scheduling tool to handle public holidays, alternating weeks, and other challenges which conventional zonal timers cannot achieve, giving you maximum control over your lighting.

Imagine you need to re-configure your office layout to suit business needs. En-trak Smart Lighting will allow you to alter your lighting configurations and zoning with a few simple clicks, regardless of the existing wiring layout. It’s as easy as that. In today’s context, getting the lighting system right is crucial. This is because, beyond simple illumination, smart lightings are in fact laying the foundation for the “Internet of Buildings”.

The potential of Smart Lightings and the Internet of Things (IoT) on buildings will be explored at the upcoming Build Eco Expo (BEX) Asia.  For the lighting industry, the opportunities are immense. The sensors and advanced controls already used in the industry can be put to even greater use to realise a truly smart building in the future. A wrong investment will be costly in such a rapidly evolving market.

###

About Author:

Dr. Vincent Chow, CEO of En-trak. En-trak is an award-winning cleantech IoT company that designs and sell cloud-based solutions to help enterprises manage and optimize their energy consumption.

Print Friendly

Leave a Reply

Your email address will not be published. Required fields are marked *

Read previous post:
SuBITech Logo - Only-1
2nd Sustainable Building & Infrastructure Technology [SuBITech] Workshop 2017

Dubai, August 2017 - The Sustainable Building & Infrastructure Technology [SuBITech] Workshop continues to stand out as the only technical...

Close